Bravo Company Mfg.

FEATURES
-Flat dark earth
-5 pack
-Made to fit ALL KeyMod mounting surfaces with seven (7) consecutive KeyMod slots
-Ultra-slim and radiused surface to allow a "round" handguard feeling
-Aggressive non-slip & non-reflective surface
-Ventilated for cooling
-Bi-directional locking tabs on either end
-5.55" x .625" x .10"
-Can be cut to any length
-Made in USA

FEATURES
-Black
-5 pack
-Made to fit ALL KeyMod mounting surfaces with seven (7) consecutive KeyMod slots
-Ultra-slim and radiused surface to allow a "round" handguard feeling
-Aggressive non-slip & non-reflective surface
-Ventilated for cooling
-Bi-directional locking tabs on either end
-5.55" x .625" x .10"
-Can be cut to any length
-Made in USA

FEATURES
-KMR Alpha
-9"
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 5.6 oz
-1.3" Inner Diameter
-1.5" OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O'Clock positions approximately 1/4"
-Actual length when measured to flare is 9.4"
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1")
-Mounting hardware, 2.4 oz, for a total of 8.0 oz on a 9" rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KMR Alpha
-8"
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 4.9 oz
-1.3" Inner Diameter
-1.5" OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O'Clock positions approximately 1/4"
-Actual length when measured to flare is 8.39"
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1")
-Mounting hardware, 2.4 oz, for a total of 7.3 oz on a 7" rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KMR Alpha
-7"
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 4.5 oz
-1.3" Inner Diameter
-1.5" OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O'Clock positions approximately 1/4"
-Actual length when measured to flare is 7.39"
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1")
-Mounting hardware, 2.4 oz, for a total of 6.9 oz on a 7" rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KMR Alpha
-15"
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 8.6 oz
-1.3" Inner Diameter
-1.5" OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O'Clock positions approximately 1/4"
-Actual length when measured to flare is 15.0"
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1")
-Mounting hardware, 2.4 oz, for a total of 11 oz on a very long 15" rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KMR Alpha
-13"
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 7.8 oz
-1.3" Inner Diameter
-1.5" OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O'Clock positions approximately 1/4"
-Actual length when measured to flare is 13.4"
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1")
-Mounting hardware, 2.4 oz, for a total of 10.2 oz on a very long 13" rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KMR Alpha
-10"
-Black
-KeyMod Free Float Handguard
-100% aluminum
-Lightweight and durable. Also featuring a proprietary patent pending mounting, indexing and lock up system that mitigates 12:00 rail movement under heat generated from the barrel nut.
-Handguard alone weighs 6.2 oz
-1.3" Inner Diameter
-1.5" OUTSIDE flat to flat
-Handguard flares forward (towards muzzle end) at the 3 and 9 O'Clock positions approximately 1/4"
-Actual length when measured to flare is 10.5"
-The KMR barrel nut will fit over all mil-spec diameter barrels (max of 1")
-Mounting hardware, 2.4 oz, for a total of 8.6 oz on a 10" rail
-The KMR Alpha is hardcoat anodized for corrosion resistance as well as to maintain a non-reflective finish.
-Includes BCM KeyMod Sling Mount

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KeyMod Picatinny Nylon Rail Section
-5.5"
-Flat Dark Earth
-Rail section is made of Lightweight Impact Resistant Polymer
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KeyMod Picatinny Nylon Rail Section
-5.5"
-Black
-Rail section is made of Lightweight Impact Resistant Polymer
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KeyMod Picatinny Nylon Rail Section
-4"
-Flat Dark Earth
-Rail section is made of Lightweight Impact Resistant Polymer
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KeyMod Picatinny Nylon Rail Section
-3"
-Flat Dark Earth
-Rail section is made of Lightweight Impact Resistant Polymer
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KeyMod Picatinny Nylon Rail Section
-3"
-Black
-Rail section is made of Lightweight Impact Resistant Polymer
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-KeyMod Picatinny Aluminum Rail Section
-5.5"
-Black
-Rail section is made of Hard Anodized Aircraft Aluminum Alloy
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

FEATURES
-KeyMod Picatinny Aluminum Rail Section
-4"
-Black
-Rail section is made of Hard Anodized Aircraft Aluminum Alloy
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

FEATURES
-KeyMod Picatinny Aluminum Rail Section
-3"
-Black
-Rail section is made of Hard Anodized Aircraft Aluminum Alloy
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

FEATURES
-Forward rake gives positive retention when using "C-clamp" method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/out significant bulk adds just the right amount of relief to the wrist w/out substantially
increasing the girth of the handguard
-Small profile is just enough to get repeatable hand position on weapon forend
-Textured in front & back for positive engagement
-Flat Dark Earth

FEATURES
-Forward rake gives positive retention when using "C-clamp" method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/out significant bulk adds just the right amount of relief to the wrist w/out substantially
increasing the girth of the handguard
-Small profile is just enough to get repeatable hand position on weapon forend
-Textured in front & back for positive engagement
-Black

FEATURES
-Foliage green
-Gunfighter Angled Grip
-Fits KeyMod version
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Flat Dark Earth
-Gunfighter Angled Grip
-Fits KeyMod Rails
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Black
-Gunfighter Angled Fore Grip
-Fits KeyMod rails
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Wolf Gray
-Gunfighter Angled Grip
-Fits Picatinny 1913 rail version
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Foliage green
-Gunfighter Angled Grip
-Fits Picatinny rail version
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Flat Dark Earth
-Gunfighter Angled Grip
-Fits picatinny 1913 rail version
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Black
-Gunfighter Angled Grip
-Fits Picatinny Rail 1913 Rail Version
-Kinesthetic Angled Grip (KAG) is designed to complement modern shooting grips
-Forward rake gives positive retention when using "C-clamp" (thumb over bore) method of handguard support
-Works as a rest for supported firing positions
-Slight angle w/o significant bulk adds just the right amount of relief to the wrist w/o substantially increasing the girth of the handguard
-Small profile is just enough to get repeatable hand positon on weapon forend
-Innovative patent pending attachment method allows for robust clamping and alignment w/ minimal hardware and slender accessory size
-Textured in front and back for positive engagement
-Made in the U.S.A. from high quality, impact resistant polymers

FEATURES
-Trigger Guard
-Mod 0
-AR-15
-Wolf Gray
-Ergonomically correct shape and contour
-No sharp edges, which enhances shooter's comfort
-Compatible with "duck-billed" grips
-Made of impact resistant polymer
-Made in USA
-Professional installation by a qualified gunsmith is required

FEATURES
-Trigger Guard
-Mod 0
-AR-15
-Foliage Green
-Ergonomically correct shape and contour
-No sharp edges, which enhances shooter's comfort
-Compatible with "duck-billed" grips
-Made of impact resistant polymer
-Made in USA
-Professional installation by a qualified gunsmith is required

FEATURES
-Trigger Guard
-Mod 0
-AR-15
-Flat Dark Earth
-Ergonomically correct shape and contour
-No sharp edges, which enhances shooter's comfort
-Compatible with "duck-billed" grips
-Made of impact resistant polymer
-Made in USA
-Professional installation by a qualified gunsmith is required

FEATURES
-Gunfighter Vertical Grip
-Picatinny
-Flat Dark Earth
-Mounted in forward angle increases rigidity of forearm, while providing more natural wrist angle when grabbing the vertical grip.
-Mounted in reverse angle to increase control when grabbing handguard and vertical grip.
-Flat sides give better yaw control during firing and non-firing manipulations
-Aggressive texture and generous storage volume combined with modular design to allow improvements and adaptation in the future.
-Cross bolt designed to work with improvised tools (such as a quarter) allow for easy adjustment or re-tightening
-Hinged trap door offering storage inside the grip with a water resistant rubber gasket
-Reversible clamps allow user to setup fasteners to reside on either side
-Spring-loaded clamp makes installation and removal easier
-Made in the U.S.A.

FEATURES
-Stock Assembly
-Mod 0
-AR-15
-Flat Dark Earth
-New patent pending latch reinvents the stock's interface with a mil-spec receiver extension, providing the user with superior strength when dropped or when mortaring malfunction clearance drill.
-Snag free Design. No sharp edges prevent tangling of the rifle with the shooter's sling, molle gear, or other kit.
-Modular VBOST (Vehicle Borne Operations Sling Tab)- This tab interfaces with the shooter's riggers' band or bungee to secure the shooter's sling against the stock when the carbine is not in use. Increasingly, this is the most common application when operating inside a vehicle.
-2 different types of ambidextrous sling mounting options, including QD swivel sockets
-Integrated color matched rubber butt pad for secure shoulder placement, along with increased durability
-Simple modular design. 5 parts, and 1 screw allow for modular adaption of future stock options and configurations.

FEATURES
-Stock Assembly
-Mod 0
-AR-15
-Black
-New patent pending latch reinvents the stock's interface with a mil-spec receiver extension, providing the user with superior strength when dropped or when mortaring malfunction clearance drill.
-Snag free Design. No sharp edges prevent tangling of the rifle with the shooter's sling, molle gear, or other kit.
-Modular VBOST (Vehicle Borne Operations Sling Tab)- This tab interfaces with the shooter's riggers' band or bungee to secure the shooter's sling against the stock when the carbine is not in use. Increasingly, this is the most common application when operating inside a vehicle.
-2 different types of ambidextrous sling mounting options, including QD swivel sockets
-Integrated color matched rubber butt pad for secure shoulder placement, along with increased durability
-Simple modular design. 5 parts, and 1 screw allow for modular adaption of future stock options and configurations.

FEATURES
-Stock Kit
-Mod 0
-AR-15
-Flat Dark Earth
-Snag free Design. No sharp edges prevent tangling of the rifle with the shooter's sling, molle gear, or other kit.
-Modular VBOST (Vehicle Borne Operations Sling Tab)- This tab interfaces with the shooter's riggers' band or bungee to secure the shooter's sling against the stock when the carbine is not in use. Increasingly, this is the most common application when operating inside a vehicle.
-2 different types of ambidextrous sling mounting options, including QD swivel sockets
-Integrated color matched rubber butt pad for secure shoulder placement, along with increased durability
-Simple modular design. 5 parts, and 1 screw allow for modular adaption of future stock options and configurations.
Also Includes:
BCM 7075T6 Mil-Spec Receiver Extension
Locking Nut M4 (Castle)
Mil-Spec Carbine Action Spring
Carbine Buffer
BCM QD Swivel Mount End Plate